You have no items in your shopping cart.
No |
CANOPY INSTALLATION GUIDE
(CCM-SBS-45410-40&50- CCM-SBS-70590-40&50)
PLEASE READ ALL INSTRUCTIONS BEFORE ATTEMPTING INSTALLATION
- To prevent personal injury or product damage only licensed electricians should install.
Installation 1. Surface Mounted with J-box
1. Loosen the screw on side of the light, removing the bracket from canopy light by pulling it out slightly, just leaving the ring on bracket.
2. Fix the bracket on J-box, and put the wire through the central hole for wiring
3. Attach the Canopy light with bracket by putting the ring on clips again. Connect the black wire for Line, white for Neutral and Yellow-Green for Ground.
4. Slide the Canopy lights into bracket, and secure the screw on side of the light to prevent the light from sliding out from the bracket. Installation done.
2. Pendent with 3/4 inch Conduit
1. Loosen the screw on side of the light, removing the bracket from Canopy light by pulling it slightly out, just leaving the ring on bracket. (See the Step 1 above)
2. Connect the wires threaded from conduit and Canopy, Black wire for Line, White for Neutral and Yellow-Green for Ground.
3. Screw the Conduit the hole on top of Canopy light
3. Surface Mount
1. Remove the lens and metal plate by unscrewing the screws.
2. Cut off the wires through from 3/4" hole and 3. Remove 1/2" plug from direction intent to feed conduit.
3. Drill 4 holes on edge of fixture and fix it on the ceiling with using appropriate screws.
4. Disconnect the wires came from 3/4" hole and connect the wires came from 1/2" conduit with power supply (White for Neutral Black for Line and Yellow Green-Green for Ground)
5. Replace the metal plate and the lens, make sure no wires are pinched when replacing parts.
Save the environment, your children and the planet
500 North Dixie Hwy, #8, Hollywood, FL 33020 – (844).533.7230
[email protected] – www.ledradiant.com
5 YEAR WARRANTY POLICY
For Commercial LED Lamps and fixtures
• This warranty policy is valid only for products sold in The United States of America.
• Products have been purchased directly from a LEDRadiant (sales) organization. • Proof of purchase is available for inspection by LEDRadiant. • Products have been properly installed and operated in accordance with the manufacturer’s instructions. • More than 10% of the LED chips are not properly working. • A LEDRadiant representative will have access to the defective Products. • If the Products or other parts become suspect, the representative shall have the right to invite other manufacturers’ representatives to evaluate the lighting systems. • Shipping and Labor costs for installation of the Products are not covered under this warranty. This warranty is valid for order number: By LEDRadiant
Save the environment, your children and the planet
500 North Dixie Hwy, #8, Hollywood, FL 33020 – (844).533.7230
[email protected] – www.ledradiant.com |
No |
CANOPY INSTALLATION GUIDE
(CCM-SBS-45410-40&50- CCM-SBS-70590-40&50)
PLEASE READ ALL INSTRUCTIONS BEFORE ATTEMPTING INSTALLATION
- To prevent personal injury or product damage only licensed electricians should install.
Installation 1. Surface Mounted with J-box
1. Loosen the screw on side of the light, removing the bracket from canopy light by pulling it out slightly, just leaving the ring on bracket.
2. Fix the bracket on J-box, and put the wire through the central hole for wiring
3. Attach the Canopy light with bracket by putting the ring on clips again. Connect the black wire for Line, white for Neutral and Yellow-Green for Ground.
4. Slide the Canopy lights into bracket, and secure the screw on side of the light to prevent the light from sliding out from the bracket. Installation done.
2. Pendent with 3/4 inch Conduit
1. Loosen the screw on side of the light, removing the bracket from Canopy light by pulling it slightly out, just leaving the ring on bracket. (See the Step 1 above)
2. Connect the wires threaded from conduit and Canopy, Black wire for Line, White for Neutral and Yellow-Green for Ground.
3. Screw the Conduit the hole on top of Canopy light
3. Surface Mount
1. Remove the lens and metal plate by unscrewing the screws.
2. Cut off the wires through from 3/4" hole and 3. Remove 1/2" plug from direction intent to feed conduit.
3. Drill 4 holes on edge of fixture and fix it on the ceiling with using appropriate screws.
4. Disconnect the wires came from 3/4" hole and connect the wires came from 1/2" conduit with power supply (White for Neutral Black for Line and Yellow Green-Green for Ground)
5. Replace the metal plate and the lens, make sure no wires are pinched when replacing parts.
Save the environment, your children and the planet
500 North Dixie Hwy, #8, Hollywood, FL 33020 – (844).533.7230
[email protected] – www.ledradiant.com
5 YEAR WARRANTY POLICY
For Commercial LED Lamps and fixtures
• This warranty policy is valid only for products sold in The United States of America.
• Products have been purchased directly from a LEDRadiant (sales) organization. • Proof of purchase is available for inspection by LEDRadiant. • Products have been properly installed and operated in accordance with the manufacturer’s instructions. • More than 10% of the LED chips are not properly working. • A LEDRadiant representative will have access to the defective Products. • If the Products or other parts become suspect, the representative shall have the right to invite other manufacturers’ representatives to evaluate the lighting systems. • Shipping and Labor costs for installation of the Products are not covered under this warranty. This warranty is valid for order number: By LEDRadiant
Save the environment, your children and the planet
500 North Dixie Hwy, #8, Hollywood, FL 33020 – (844).533.7230
[email protected] – www.ledradiant.com |